Grommet for cabin air hose in boot
-
- E Class
- Posts: 54
- Joined: Wed 12 Aug, 2015 5:15 pm
- Model you own: w108
Grommet for cabin air hose in boot
Hi, I'm looking for one of these grommets in good condition. Have gone to MB Classics in california but they say NLA. Has anyone got one in good condition they want to sell plse? Photos attached of grommet without piece that fitis into the boot floor, and a general shot of the boot showing cabin air hose hanging loose.(shot at right angles sorry)
You do not have the required permissions to view the files attached to this post.
- TheMadRacoon
- C 111
- Posts: 967
- Joined: Sun 25 Nov, 2012 11:34 am
- Model you own: w107
- Location: Melbourne
Re: Grommet for cabin air hose in boot
This part looks like a good candidate for 3D printing if NLA. Presumably it requires to be slightly flexible so as to seal, rather than rigid.
Perhaps look up some of the 3D threads, some of the 3D enthusiasts might be willing to help?
Perhaps look up some of the 3D threads, some of the 3D enthusiasts might be willing to help?
Emad,
TheMadRacoon
1975 350SLC Astral Silver (725) / Blue (2012 - 2019.... an under-rated car)
1988 190E Deep Blue (900) / Cream (2006, 190,000 km - 2007, ~ 215,000 km .... FSH and still spent big $$$)
1974 280E Reed Green (860) / Bone (1993, 316,700 km - 2004, ~490,000 km and still A1)
TheMadRacoon
1975 350SLC Astral Silver (725) / Blue (2012 - 2019.... an under-rated car)
1988 190E Deep Blue (900) / Cream (2006, 190,000 km - 2007, ~ 215,000 km .... FSH and still spent big $$$)
1974 280E Reed Green (860) / Bone (1993, 316,700 km - 2004, ~490,000 km and still A1)
-
- E Class
- Posts: 54
- Joined: Wed 12 Aug, 2015 5:15 pm
- Model you own: w108
Re: Grommet for cabin air hose in boot
Hi there, you are right, the problem is finding someone with a 3D printer round auckland to do it.
- TheMadRacoon
- C 111
- Posts: 967
- Joined: Sun 25 Nov, 2012 11:34 am
- Model you own: w107
- Location: Melbourne
Re: Grommet for cabin air hose in boot
Postage from Oz for a part like that wouldn't be too expensive I would think.
Emad,
TheMadRacoon
1975 350SLC Astral Silver (725) / Blue (2012 - 2019.... an under-rated car)
1988 190E Deep Blue (900) / Cream (2006, 190,000 km - 2007, ~ 215,000 km .... FSH and still spent big $$$)
1974 280E Reed Green (860) / Bone (1993, 316,700 km - 2004, ~490,000 km and still A1)
TheMadRacoon
1975 350SLC Astral Silver (725) / Blue (2012 - 2019.... an under-rated car)
1988 190E Deep Blue (900) / Cream (2006, 190,000 km - 2007, ~ 215,000 km .... FSH and still spent big $$$)
1974 280E Reed Green (860) / Bone (1993, 316,700 km - 2004, ~490,000 km and still A1)
- Mercmad
- Mercedes Demigod
- Posts: 8107
- Joined: Sun 11 Sep, 2005 8:01 pm
- Model you own: w109
- Location: Brissy
- Contact:
Re: Grommet for cabin air hose in boot
Theres a guy in the vintage car club n Auckland who is a wizard with 3d printing ,can't remember his name off hand but he has a done of lot of modelling for car restorers in NZ for car parts.
-
- E Class
- Posts: 54
- Joined: Wed 12 Aug, 2015 5:15 pm
- Model you own: w108
Re: Grommet for cabin air hose in boot
Hi thanks for that last one, I will get in touch with them